LEGO F1 Display Ideas: Plan a Wall for Two, Three or More Cars

LEGO F1 Display Ideas: Plan a Wall for Two, Three or More Cars

One LEGO Formula 1 car makes a great display. Put a few together and you can create your own racing gallery — with favourite teams, contrasting liveries and space for the next build.

The trick is planning the collection as a whole. A good layout gives each model room to stand out, fits the wall you actually have and remains easy to extend. Here are some practical LEGO F1 display ideas for a pair of cars, a three-car line-up or a growing collection.

Start with the cars you own and the space you have

Make a list of your models and their LEGO set numbers before choosing mounts. Similar team names do not mean the same bracket will fit: the McLaren Formula 1 2022 car is set 42141, while the McLaren MCL39 is 42228.

Next, measure your usable wall space. Allow for opening doors, nearby furniture and the depth of the mounted cars. Think about where you will view them from, as well as how you will reach them to fit, remove and dust them.

Keep these three measurements for each model: its full length, its widest point and how far it will project from the wall in the intended mounting position. Wings and tyres matter just as much as the main body.

Idea 1: a two-car display with room to grow

A pair is an easy place to start. You could display your favourite team alongside a rival, or choose two liveries that complement each other.

The orange McLaren MCL39 (42228) and green Aston Martin AMR25 (42240) make a distinctive combination. Both have vertical and horizontal mounts in our range, giving you two straightforward arrangements to consider:

  • Two vertical cars side by side: a good starting point if you expect to add more cars across the wall.
  • Two horizontal cars stacked: keeps the overall width close to the length of one car, with space around it, and leaves scope to add another above or below.
LEGO Technic McLaren MCL39 and Aston Martin AMR25 F1 cars mounted horizontally, one above the other, on a study wall
A two-car idea: the MCL39 and AMR25 displayed horizontally in a stack.

To recreate the horizontal pair: choose the MCL39 horizontal mount and AMR25 horizontal mount. Both offer facing-left and facing-right options, so decide whether you want the cars pointing the same way before ordering.

Prefer an upright pair? Choose the MCL39 vertical mount and AMR25 vertical mount instead.

Idea 2: a three-car racing line-up

Three cars make a natural centrepiece: one in the middle, with another on either side. A vertical row lets you see the colours and shapes together without spreading the display across the combined lengths of three horizontal cars.

The Ferrari SF-24 (42207), McLaren MCL39 (42228) and Red Bull RB20 (42206) are one combination, shown below. Try swapping the order on a sketch before deciding which car belongs in the centre.

Red Bull RB20, McLaren MCL39 and Ferrari SF-24 LEGO F1 cars mounted together on a wall
A three-car row featuring Red Bull, McLaren and Ferrari.

Mounts for this line-up: Ferrari SF-24 vertical mount, McLaren MCL39 vertical mount and Red Bull RB20 vertical mount.

You can use the same approach with a different selection of teams. The Ferrari, Mercedes W14 and Aston Martin AMR25 offer another colour combination:

LEGO Technic Ferrari SF-24, Mercedes W14 and Aston Martin AMR25 F1 cars displayed together on a wall
Another collection idea: Ferrari, Mercedes and Aston Martin. Choose the combination that suits your collection.

For that selection, use the SF-24 mount, Mercedes W14 mount for set 42171 and AMR25 mount.

Idea 3: plan a larger F1 gallery in rows or columns

For four or more cars, decide how the display should grow. A single row of vertical cars is simple to extend sideways. Two rows can work better when wall width is limited. A column of horizontal cars is another option when you have more height than width.

Do not feel you have to fill a grid immediately. You can plan six positions and start with four cars, leaving space for models you genuinely want to build next.

If you mix large Technic cars with smaller Icons or Speed Champions models, group them deliberately. A separate row for each size often makes the differences look intentional. Always check compatibility and the available mounting positions for each set.

How much wall space will your display need?

Use your own measurements to calculate the outline of the finished arrangement. For a row of vertical cars:

Total width = the combined widths of the cars + the gaps between them + the margins at each end.

Total height = the height of the tallest displayed car + the margins above and below.

For a horizontal stack, apply the same principle in the other direction. Include any extra clearance needed to place the models onto their brackets and remove them.

A worked example: suppose each car occupies a rectangle 60 cm long and 25 cm wide. Choose 10 cm gaps between cars and 10 cm margins around the outside.

These are illustrative planning measurements, not specifications for the pictured sets. The gaps are a layout choice, not a minimum installation clearance. Measure your own models and follow their fitting instructions.

Example wall area using those assumed measurements
Arrangement Width Height
Two vertical cars side by side 80 cm 80 cm
Three vertical cars in one row 115 cm 80 cm
Five vertical cars in one row 185 cm 80 cm
Six vertical cars in two rows of three 115 cm 150 cm
Three horizontal cars in a stack 80 cm 115 cm

For the three-car row, for example, the width is 25 + 25 + 25 cm for the cars, 20 cm for the two gaps and 20 cm for the outer margins: 115 cm altogether.

Before drilling, use paper outlines or a scale drawing to check the arrangement. This makes it much easier to spot a layout that looks crowded or will not fit.

Align the cars, rather than the screw holes

Different models can have different distances between the bracket and the front of the car. A level row of fixing holes will not necessarily give you a level row of noses.

  1. Choose your reference line. For upright cars, this might be the noses or rear wings.
  2. Position each bracket on its model as instructed. Measure from the fixing point or points to that reference.
  3. Mark the model positions on your plan. Allow for each car’s full width and your chosen gaps.
  4. Transfer the individual fixing positions to the wall. Check them against the instructions before drilling.

For mixed-size models, aligning their centres may look better than matching their fronts. There is no single correct arrangement: choose one consistent rule and check the result before fitting.

Build a shopping list for the finished display

Once you have chosen a layout, check each car against this short list:

  • The exact LEGO set number.
  • The intended display orientation.
  • The facing direction, where the product offers a choice.
  • The quantity required for that model.

You can start with a pair and add to the display over time. You do not need to buy mounts for cars you have not chosen yet; simply leave the space in your plan.

Our brackets are designed and 3D-printed by us in the UK and supplied with fixings and installation instructions. Choose an appropriate wall position and check the fixing method for your wall using the installation instructions. LEGO models are not included.

Find the wall mounts for your LEGO F1 collection

If you need help matching a bracket to your model, contact us with the set number and the mounting position you have in mind.


More planning help: How to Create a LEGO Display Wall · The Ultimate Guide to Wall-Mounting LEGO Models

Choosing an orientation? Read Vertical or Horizontal? Choosing a Wall Mount for Your LEGO F1 Car before deciding which bracket to order.

LEGO is a trademark of the LEGO Group, which does not sponsor, authorise or endorse 3Dudes & Dad.

Back to blog
3Dudes & Dad Wall Mount Bracket for LEGO Technic Land Rover Defender (set 42110)

Ready to create your own LEGO display?

Browse the range and find the perfect wall mount for your LEGO Technic, Star Wars, Speed Champions, DC & Icons models.

Shop now